Bostik
Address: 211 Boston St., Middleton, MA 01949URL/Email Address: www.bostik-us.com
Phone: (978) 750-7321
Fax: (978) 750-7212
Product Names: Bostik’s Ultra-Set® SingleStep™ is a one-part, trowel applied, tacking, moisture-cure urethane adhesive, moisture vapor and sound reduction membrane. This scientifically-formulated adhesive and membrane is very tenacious, has very low moisture permeability, and is formulated with patent pending Thickness-Control™ Spacer Technology to ensure proper membrane thickness between hardwood flooring and the substrate. The product does not contain any water, and has zero VOC as per SCAQMD 1168. MVP4® Moisture Vapor Protection is a one-part, trowel applied, elastomeric, moisture cure urethane membrane designed to reduce moisture vapor transmission from the subfloor; create a noise reduction barrier over the substrate; and establish an anti-fracture membrane that can bridge cracks that can occur in the substrate prior to or after installation (up to 1/8”) of engineered and solid hardwood flooring. MVP4 may be used over all substrates for hardwood flooring installations including: concrete, plywood, particle or chip board (underlayment grade), well bonded vinyl, ceramic tile, cement backer board, cement patch/underlayments, radiant heat flooring, and terrazzo. MVP4 contains Bostik BLOCKADE™ antimicrobial protection. Hydroment Ultra-Set Advanced elastomeric waterproofing/crack/sound isolation membrane and setting adhesive can be used over properly prepared concrete; structurally-sound, exterior grade plywood (interior/dry use only); cementitious backer board; and existing, well-bonded vinyl/VCT or ceramic tile; prior to the installation of ceramic or stone tile. Ultra-Set Advanced may be used with gypsum-based underlayments in dry, above grade installations with minimum compressive strengths of 2,000 psi.
Cork Direct
Address: 2211 Lithonia Industrial Parkway, Lithonia, GA 30058URL/Email Address: www.corkdirect.com; info@corkdirect.com
Phone: (800) 344-CORK (2675)
Fax: (770) 484-0893
Product Names: CorkDirect Half-inch Premium European Underlayment – 1/2” x 24” x 36” - 6 sq. ft. per sheet; Sold in boxes of 25 sheets, 150 sq. ft. at low prices. Significant discounts for larger quantities, time critical delivery. CorkDirect Quarter-inch Premium European Underlayment – 1/4” x 24” x 36” - 6 sq. ft. per sheet; Sold in boxes of 50 sheets, 300 sq. ft. at low prices. Significant discounts for larger quantities, time critical delivery. CorkDirect Quarter-inch Premium European Underlayment in rolls – Sold in rolls 1/4” x 4’ x 50’ - 200 sq. ft. per roll at low prices. Significant discounts for larger quantities, time critical delivery. CorkDirect Eighth-inch Premium European Underlayment in rolls – Sold in rolls 1/8” x 4’ x 50’ - 200 sq. ft. per roll, at low prices. Significant discounts for larger quantities, time critical delivery.
Custom Building Products
Address: 13001 Seal Beach Blvd., Seal Beach, CA 90740URL/Email Address: www.custombuildingproducts.com
Phone: (800) 272-8786
Product Names: EasyMat® Tile & Stone Underlayment –EasyMat with SoundGard® Technology is a versatile underlayment that is 25X lighter and 4X faster to install than backerboard. It offers a bonded anti-fracture system, reduces impact sound transmission and qualifies for our system’s lifetime warranty.
Hacker Industries, Inc.
Address: 1600 Newport Center Drive, Ste 275, Newport Beach, CA 92660URL/Email Address: www.hackerindustries.com; info@hackerindustries.com
Phone: (949) 729-3101; (800) 642-3455
Fax: (949) 729-3108
Product Names: FIRM-FILL Brand Gypsum Concretes – Poured gypsum concrete floor underlayments that offer sound and fire resistance properties paired with exceptional compressive strengths. Ideal for use over wood, steel deck, concrete and radiant heat systems. Only installed by trained Licensed Applicators. FIRM-FILL® SCM (Sound Control Mat) – A 3mm sound control mat that achieves superior sound reduction with minimal height differences. A cost-effective sound control solution for multi-family construction. Requires a ¾” FIRM-FILL Brand Gypsum Concrete topping. Hacker Sound Mat –A 2mm recycled rubber sound mat helps isolate sound transmission between floors in multi-family construction. Requires a ¾” FIRM-FILL Brand Gypsum Concrete topping. Hacker Sound Mat II – A durable, environmentally friendly sound control mat composed of recycled rubber that helps increase STC and IIC values, creating a quieter living environment. Requires a 1-1/4” FIRM-FILL Brand Gypsum Concrete topping.
Keene Building Products
Address: P. O. Box 241353, Mayfield Heights, OH 44124Phone: (877) 514-5336
Fax: (440) 605-1120
URL/Email Address: www.keenebuilding.com; info@keenebuilding.com
Product Names: QQ Step Soft™ 1mm to 8mm are sound deadening products designed for use with the Quiet Qurl® system where hard surface flooring will be used. Recommended as a means to suppress cracks in tile applications while controlling impact noise, especially at the high frequencies. The recycled rubber mat can earn LEED credits; its composition is 100% recycled rubber. Quiet Qurl® 55/025 MC MT is a nominal 0.25”, random filament, corrugated, “U” Groove core sound control mat designed to limit impact noise between floors. Layers consist of a moisture control fabric, entangled net core & white polyester fabric. The point bonded, moisture resistant fabric is laminated to the surface so that gypsum concrete & other materials can be used to create a floating floor. On the bottom side is a highly compressible bonded polyester fabric. Quiet Qurl® RF is an alternative for all three versions of the standard Quiet Qurl product. It is designed for use when the gypsum concrete pour is not to standard thickness (1” with QQ 55/025, 1.5” with QQ 60/040 and always with QQ 65/075). The product combines a fiberglass fabric and a fiberglass scrim together, in combination with the standard entangled net core material. A fiberglass fabric is laminated to the surface so that gypsum concrete or concrete can be placed to create a floating floor. Quiet Qurl® Reinforcement RWT-040 is a 0.375” (9 mm), random filament, geometric patterned core crack suppression mat used to reinforce gypsum concrete & many types of concrete in thin applications. The 3/8” (8 mm) thickness product provides the added strength needed in the assembly when the gypsum concrete is less than traditional 1½” (50 mm) topping.
MAPEI Corporation
Address: 1144 E. Newport Center Dr., Deerfield Beach, FL 33442URL/Email Address: www.mapei.com
Phone: (954) 246-8888
Fax: (954) 246-8801
Product Names: Mapeguard™ 2 Premium Crack-Isolation and Sound-Reduction Sheet Membrane is a next-generation, flexible thin, 40-mil lightweight, load-bearing, fabric-reinforced “peel-and-stick” crack-isolation membrane. After application, ceramic tile or stone can be installed immediately with any polymer-modified cement-based mortar (ANSI A118.4 or better). Glue-down wood flooring can also be installed with any MAPEI urethane adhesive. Mapeguard 2 helps prevent existing or future in-plane floor cracks (with movement up to 3/8” [10 mm] wide) from transmitting through grout, ceramic tile or natural stone. It also reduces impact sound (footsteps, dropped objects, etc.) and airborne sound (voice, TV, etc.) transmission through floors when installed under ceramic tile, stone or wood flooring.
Maxxon Corporation
Address: 920 Hamel Rd., Hamel, MN 55340URL/Email Address: www.acousti-mat.com; info@maxxon.com
Phone: (800) 356-7887
Fax: (763) 478-2431
Product Names: Acousti-Mat® II – The low profile, cost-effective solution to noise complaints with ceramic and wood floors. Enkasonic® – A durable and proven solution - the mat that has been tested after 10 years of use. Acousti-Mat® 3 – The sound deadening solution for floor systems that have been impossible to control - even with open beam, concrete slab and conventional wood frame systems. Acousti-Mat® LP – Achieves a Delta IIC of 19, an approximate 75% reduction in impact noise in concrete construction. Acousti-Mat® LPR – With a total system height of ¾”, the Acousti
MP Global Products LLC
Address: P.O. Box 2283, Norfolk, NE 68702Phone: (888) 379-9695
Fax: (402) 379-9737
URL/Email Address: www.quietwalk.com; mwp@mpglobalproducts.com
Product Names: QuietWalk – Underlayment for floating wood and laminate flooring deadens the transfer of sound between rooms and improves the ambient sound within the room. Made of recycled materials for a truly green building product. QuietWarmth – All the acoustical benefits of QuietWalk with the added feature of radiant heat for laminate, wood and tile flooring. Insulayment – Acoustical underlayment similar to QuietWalk but designed for glue-down or nail-down wood; can also be used beneath ceramic tile for sound abatement and crack suppression. AbsorbaSound – A lightweight cross-link polyethylene foam acoustical underlayment. NoiseBlock – A dense cross-link polyethylene foam acoustical underlayment. SoundStep – A frothed rubber acoustical underlayment.
Merkrete
Address: 4125 E. La Palma Ave., Anaheim, CA 92807URL/Email Address: www.merkrete.com; mark.cooke@parexusa.com
Phone: (714) 778-2266
Fax: (714) 774-2079
Product Names: Sound Shield 7000 is a fiber reinforced rubber sound suppressing mat and crack isolation membrane incorporating a polyester fabric layer on each side to enhance adhesive strength. It is 1/8” thick and available in 42” x 48” sheets, suitable for use under hard surface finishes such as tile, stone and hardwood flooring. Made from recycled materials, and with zero VOC, Sound Shield 7000 contributes to LEED projects. Sound Shield PNS 40 and PNS 90 are peel and stick rubberized asphalt base sound controlling and crack isolation membranes in either 40 mil. or 90 mil. thicknesses. The roll of membrane includes a heavy film laminated to the face of the sheet and a siliconized, removable release sheet on the adhesive side. The system includes a specially formulated Prep Seal PNS primer that insures proper adhesion to the substrate. Sound Shield PNS 40 and 90 are suitable under tile and ceramic stone for both residential and commercial applications. 801 Self-Curing Hydraulic Thin Set is a quick-setting mortar designed to cure without the need for normal evaporation. Designed for use with Sound Shield products, 801 Thin Set is recommended for all non-porous applications.
QT Sound Insulation by ECORE International
Address: 715 Fountain Ave., Lancaster, PA 17601URL/Email Address: www.qtsoundcontrol.com
Phone: (866) 326-5712
Fax: (717) 295-3414
Product Names: QTscu; QTrbm
RB Rubber Products
Address: 904 NE 10th Ave., McMinnville, OR 97128URL/Email Address: www.rbrubber.com
Phone: (503) 472-4691
Fax: (503) 434-4455
Product Names: RB Silent-Tread; RB Silent Tread XL (with moisture barrier)
Stauf Adhesives, USA
Address: 6055 Primacy Pkwy, Ste 428, Memphis, TN 38119URL/Email Address: www.staufusa.com; info@staufusa.com
Phone: (901) 820-0007
Fax: (901) 820-0101
Product Names: SMP-960 ONE-STEP – Provides STC and IIC sound ratings of 72 & 74 dB plus moisture barrier up to 12#, all in one application. Easy to spread and clean. Suitable for any width, thickness, length and specie of wood flooring. Meets LEED requirements. No VOC’s, carcinogens, nor etching of the floor finish. Anti-microbial. Certified Green by GEV. Non-flammable. Completely environmentally safe.
wedi Corporation
Address: 1100 Landmeier Rd., Suite 200, Elk Grove Village, IL 60007Phone: 877-933-WEDI (9334)
Fax: (847)-357-9819
URL/Email Address: www.wedicorp.com; bastian.lohmann@wedicorp.com
Product Names: wedi® Subliner Dry & Flex Pro is a peel and stick, flexible underlayment with integral waterproofing, anti-fracture and sound reducing characteristics. The underlayment is made from highly tear-resistant, nonwoven polypropylene material with a rubberized asphaltic, pressure sensitive adhesive layer; offers optimum adhesion to tile laying materials due to its special fleece lamination. Can be used with ceramic tiles, slabs and natural cast tiles in indoor and outdoor floor areas; and provides improved tension compensation during abrupt temperature changes. wedi® Subliner Dry & Flex Pro is 100% waterproof and effectively protects subfloors from moisture damage and cracks due to movement. Must be used with wedi® primers. Crack isolation up to 3/8” lateral movement. wedi® Subliner Dry & Flex Pro successfully passed and exceeded ANSI A118.12-1999 requirements.
Editor’s Note:The listings included in the Sound Control Solutions Primer are all sponsored listings. Please contact publisher Jeff Golden at (818) 224-8035 ext. 2218 or your media consultant to be part of the feature online.
Report Abusive Comment